Gateway E-9520T User Manual Page 66
- Page / 114
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
CHAPTER 6: Troubleshooting
60
Boot messages
Boot Failure ...
This is a generic message indicating the BIOS could not boot from a particular device. This message
is usually followed by other information concerning the device.
Invalid Boot Diskette
A diskette was found in the drive, but it is not configured as a bootable diskette.
Drive Not Ready
The BIOS was unable to access the drive because it indicated it was not ready for data transfer.
This is often reported by drives when no media is present.
A: Drive Error
The BIOS attempted to configure the A: drive during POST, but was unable to correctly configure
the device. This may be due to a bad cable or faulty diskette drive.
Insert BOOT diskette in A:
The BIOS attempted to boot from the A: drive, but could not find a correct boot diskette.
Reboot and Select proper Boot device or Insert Boot Media in selected Boot device
BIOS could not find a bootable device in the system and/or removable media drive does not contain
media.
NO ROM BASIC
This message occurs on some systems when no bootable device can be detected.
Storage Device messages
Primary Master Hard Disk Error
The IDE/ATAPI device configured as Primary Master could not be correctly initialized by the BIOS.
This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI
devices in POST.
Primary Slave Hard Disk Error
The IDE/ATAPI device configured as Primary Slave could not be correctly initialized by the BIOS.
This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI
devices in POST.
Secondary Master Hard Disk Error
The IDE/ATAPI device configured as Secondary Master could not be correctly initialized by the BIOS.
This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI
devices in POST.
Secondary Slave Hard Disk Error
The IDE/ATAPI device configured as Secondary Slave could not be correctly initialized by the BIOS.
This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI
devices in POST.
Primary Master Drive - ATAPI Incompatible
The IDE/ATAPI device configured as Primary Master failed an ATAPI compatibility test. This message
is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices in POST.
Primary Slave Drive - ATAPI Incompatible
The IDE/ATAPI device configured as Primary Slave failed an ATAPI compatibility test. This message
is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices in POST.
- USERGUIDE 1
- Contents 3
- Connectors and LEDs 9
- Interior 10
- System board 11
- Hot-swap backplanes 12
- LED information 13
- Getting Help 14
- Setting Up Your Server 15
- Setting up the hardware 16
- Retaining tab 17
- Starting your server 19
- Initial hardware settings 20
- Maintaining Your Server 21
- Caring for your server 22
- Preparing for system recovery 23
- System administration 23
- Identifying your server 24
- Server Companion DVD contents 25
- Viewing documents 25
- Installing Components 29
- Selecting a place to work 30
- Gathering the tools you need 30
- Opening the server case 31
- Closing the server case 32
- Filling empty drive bays 37
- Installing memory 39
- Replacing system fans 44
- Connect to Mezzanine Board 53
- Replacing the CMOS battery 54
- Replacing the system board 55
- Using the BIOS Setup Utility 57
- Updating the BIOS 58
- Recovering the BIOS 59
- Resetting the BIOS 60
- Resetting BIOS passwords 61
- Updating the BMC firmware 62
- Recovering the BMC 62
- Troubleshooting 63
- Telephone support 64
- Tutoring and training 65
- Safety guidelines 65
- Error messages 65
- Boot messages 66
- Storage Device messages 66
- System configuration messages 67
- CMOS messages 68
- Sensor type codes 69
- Battery replacement 71
- Beep codes 71
- Diagnostic LEDs 73
- POST code checkpoints 74
- Description 75
- DIM code checkpoints 78
- Optical drive 79
- Expansion cards 79
- Hard drive 80
- Internet 80
- Keyboard 80
- Processor 81
- CHAPTER 6: Troubleshooting 82
- System specifications 84
- System board specifications 84
- Environmental specifications 85
- Electronic specifications 86
- Connector pinouts 87
- VGA connector (J24) 88
- Mini-SAS connectors (J50) 88
- Pin Signal Name 89
- Serial port connector (J15) 90
- Keyboard and Mouse connectors 90
- External USB connectors 90
- Additional specifications 91
- Advanced 94
- Security 98
- APPENDIX B: BIOS Settings 100
- BIOS submenu BIOS 2nd level 101
- Setting Value 101
- Configuration 102
- APPENDIX 103
- United States of America 104
- Laser safety statement 105
- Environmental information 106
- Important safety information 108
- A MAN E-9520T GDE R3 05/07 114
Related products and manuals for Servers Gateway E-9520T
Servers Gateway TT.R5900.108 Datasheet
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 5.209 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals